New Moves for Big, Athletic Hamstrings
Add some meat to your hamstrings, increase sports performance, and prevent injuries with these challenging new exercises.
A great set of hamstrings will always stand out. Building them can even help protect the knees and prevent injuries. Here are some new moves that’ll add more meat to your hamstrings.
1. Slider Hamstring Curl with Slow Eccentric
You’ve probably heard of Nordic curls and the benefits of controlled eccentrics (lowering slowly), particularly for hamstring injury prevention. Well, this is a good alternative that similarly benefits your hamstrings. Exercises like these also tend to bias more biceps femoris, which is useful for “outer” hamstring development.
The lifting portion is a glute bridge – much easier to do with a heavier weight because you’re at a greater mechanical advantage. On the way down, you do something resembling a leg curl, which is possible with sliders. During this part, the hamstrings are at a mechanical disadvantage, so more work is required at the same relative load on the way down.
The result of all this? An overload of the hamstrings during the eccentric portion of the lift.
Like Nordic curls, these can mess up your hamstrings for days, so watch the volume. Just 2-3 sets of 5-8 reps with a controlled negative work best to start. Add an extra set or two as your hamstrings become more accustomed.
2. Dumbbell Hamstring Walk
This exercise is relatively simple but deceptively difficult. If you’ve got good hamstrings, then these shouldn’t be a challenge. If your hamstrings or gastrocnemius (the big meaty part of your calf) are a little out of condition, though, cramping is common.
Keep your feet as narrow as possible on the dumbbell and point your toes. Having your feet close together will stop the dumbbell from steering off in one direction. You can also use a foam roller.
By plantar-flexing your ankles (like a ballerina) you’ll create a co-contraction of your calves and hamstrings. This co-contraction increases the activation of the hamstrings. The active insufficiency of the gastrocnemius muscle causes your hamstrings to work harder. Don’t believe it? Just try any ham curl machine with a plantar-flexed position and note the difference.
Walk the dumbbell up to the point just before you lose hamstring tension. You’ll know when. Walk it back down as far as you can, getting as long as you can with your toes pointed.
That’s one rep. Go for 3-5 full reps and don’t let off the tension. Add reps over time, or try it with a bar across your hips for some extra nastiness.
3. Band Prone Hamstring Curl
When choosing exercises, one of your main considerations should be muscle length. Exercises that train muscles in their longest position (think hips bent with knees straight) do a great job, but so do exercises that train them in their shortened position (think hips straight with knees bent).
Banded hamstring curls put your hips in a straightened position, working through knee flexion. With this position and the ascending band resistance, these load the hamstrings most in their shortened position. Because of this, these do a crappy job of training your hamstrings in their lengthened position, but the squeeze and pump you get more than make up for it.
Combine them with something more hip-dominant (like RDLs, back extensions, pull-throughs, etc.) to cover all bases. Sets of 20-30 reps work well toward the back end of a workout. Or you could start with them – your squats will feel smoother after you get a hamstring pump.
4. Landmine Single-Leg RDL – Ipsilateral
Single-leg RDLs are most commonly done with a contralateral load: load in the opposite hand of the planted foot. Contralateral work is great for athletic development, but if you care more about getting bulging hamstrings, focus on Ipsilateral work.
“Ipsilateral” means using the same-side arm and leg. An ipsilateral RDL tends to be more stable, and it emphasizes the lead leg’s hamstring more. You can do these front facing or side facing.
A dumbbell or kettlebell will work, but if you’re looking to really load those hamstrings (and glutes), using a landmine offers more stability. The bar stays in contact with the floor throughout the lift. More stability means more output, so it can be a good way to bro-up your single-leg work.
These work well with a variety of rep ranges.
5. Hip-Banded RDL
Since your hamstrings are made up of a disproportionate amount of fast-twitch muscle fibers, include heavy exercises.
That said, you may argue that stiff-legged deadlifts are more hamstring-dominant than Romanian deadlifts, and you’d be right. However, there’s less low-back stress during an RDL because the load is closer to the axis of rotation and closer to the base of support. This means when you’re looking to go heavy, RDLs are the superior choice.
The hip-banded RDL is a good way to load your hamstrings and glutes. Having a band pulling your hips back has obvious advantages for promoting correct RDL technique and can be a useful extrinsic coaching cue if you’re new to them.
Using the setup shown in the video enables you to use more band resistance. You’ll be able to double up the band and have more control. Bonus: It seems to promote a better hip hinge – there’s something to hinge (take a bow) over.
Of course, the band helps to add horizontal load through the hips, making it a potent butt-builder as well. To develop your hamstrings and the rest of your posterior chain, sets of 6-8 work well here.
You can steer clear of locking out, working a two-thirds movement at the bottom, for more hamstring bias. Alternatively, you can lock out at the top with some posterior pelvic tilt for extra butt stuff.
6. Triple-Threat Hamstring Bridge
Your hamstrings need to be trained at different lengths. One of the best descriptions of this came from Mr. Olympia, Jay Cutler, who said, “Do some exercises to squeeze the muscle and some exercises to stretch it.”
When it comes to lower-body workouts, many lack variety for the hamstrings and, as a result, lack emphasis on different joint angles and muscle lengths. This leads to underdeveloped hamstrings and sacrificed strength. It can also leave you more vulnerable to injury.
So make sure you have some variety. Start with picking one hip-dominant hamstring exercise (RDL, back extension, pull-through, etc.) and one knee-flexion-based exercise (hamstring curls, GHRs, Nordics) per workout.
You can also do exercises that cover a lot of joint angles and even combine isometric holds. Isometrics help activate high-threshold motor units and can create lots of metabolic stress – a potent muscle growth stimulus.
When done as a mechanical drop set, you’ll begin in your weakest position at a longer hamstring length, with toes pointed. Then move to a slightly shorter position with toes pointed. Finally, move to a traditional hamstring bridge pulling with your heels. Do 5-10 reps in each position, each with a 5-10 second isometric hold.
T Nation earns from qualifying purchases as an Amazon Associate. Read more about our policy.