10 Fresh Ways to Build Your Hamstrings

Build bigger, stronger hamstrings in four weeks.

Most lifters assume the deadlift and squat are enough to build their hamstrings, but that’s only one small portion of what’s needed to make them jacked.

Addressing limitations is critical to consistent improvement in maximal strength and also for strength endurance. So if you’re not considering where you’re weakest, now’s the time to start.

Both closed chain (think RDL) and open-chain settings (think hamstring curl variations) should be part of your routine. Both are covered here. Start applying these to your lower-body workouts and see results in as little as four weeks.

The Glute-Ham Raise and Inverse Leg Curl

This is the GHR (glute-ham raise), and you’d be hard-pressed to find a better variation to crush your hamstrings than it – aside from the inverse leg curl (below) – but most gyms simply don’t offer that level of equipment.

Fortunately, most CrossFit boxes do have glute-ham raises. This certainly isn’t a beginner variation, so check out the full video for some great scaling options.

If you’re fortunate enough to have access to an inverse leg curl, think of it as a progression from the GHR.

General programming: Add either movement to your leg workout by accumulating 30-50 reps with varying levels of resistance.

The Sled Pull with Straps Between Legs

The best part of using the sled is that it requires almost zero skill. If you know how to walk, you’ll be good to go. Load the sled heavy while still being forceful on every step.

Programming for strength: Do 6-10 sets x 60 yards
Programming for strength endurance: Accumulate 400-800 yards

The Sumo RDL with Band

While the sumo RDL is a proven exercise, you can adjust it by using reactive neuromuscular training (RNT). You’ll notice that the bands are pulling forward. This is going to force you to dial in a solid position and engage the anterior core and posterior chain to even greater extent. You can do this with a conventional or sumo stance.

General programming: Do 4 sets of 8-10 reps

The RDL with Reverse Bands (Future Method)

Using reverse bands, or as Westside calls it, “the future method,” is an incredibly powerful tool to alter loading through range of motion. The bands unload at the top of the movement, allowing you to work with heavier loads than normal.

While this method is often used for max effort work, it can also be used for repetition effort (high rep) work as well. One caveat though: If you’re using the future method for max effort work, use it sparingly since it’s demanding on the nervous system.

  • Programming for max effort work: Build to a 1RM in 10 sets
  • Programming for repetition effort work: 4-5 sets x 6-10 reps

The Single-Leg Supported RDL

You’ll love this variation because you can increase loading without being limited by balance, though this certainly doesn’t replace the standard unsupported version. Instead, this is a progression for those who’ve mastered the unsupported version.

General programming: 4-5 sets x 6-8 reps for each leg

The Single-Leg Landmine RDL

The landmine can satisfy just about any training need, so it’s no surprise we’re able to train the hamstrings quite effectively with this exercise. If you’re looking to complement your training with an unsupported variation, this is it. Unlike the supported RDL, the goal here is to work with lighter loads in higher-rep strength endurance settings.

General programming: Do 2-3 sets x 10-15 reps for each leg

The Banded Hamstring Curl

No ham-building list would be complete without a band variation to improve the quality of tendons and their elastic abilities. The purpose of band work is mainly for injury prevention. Usually this will be done as high-rep finisher.

General programming: Accumulate 100 reps, as fast as possible

The Trap Bar Deadlift – Touch & Go

Higher-rep deadlifts are an effective tool, but are often used haphazardly where people will sacrifice their lumbar spine for loading/cycle rate. Take a look at just about any CrossFit competitor performing high-rep deadlifts in a conditioning setting and you’ll be hard-pressed to find a neutral spine.

With the trap bar, the weight is positioned closer to the center of your mass, creating a different joint angle or gravity line allowing you to train bilaterally with less risk of mechanical breakdown. For most though, I’d recommend first pulling from a 2-4 inch elevated surface (like plates) for at least a few sessions.

General programming: Do 4-5 sets x 6-8 reps at 70-75% of 1RM

The Wide-Stance Box Squat

We’ve gone through the box squat more than a few times and it’s been the topic of debate for years. We’ve covered it before, but if you’re ready to implement the box squat it can be done a few ways.

You’ll want to use a height that puts you at parallel or slightly higher to ensure the movement remains hip dominant. And you’ll need to watch the full video demo to make sure you don’t miss some of the key points. If you’re still learning to box squat, stick with a submaximal effort or dynamic effort method before attempting a max effort.

Programming for dynamic effort: Do 8 sets x 3 reps at 60% of your 1RM, resting 60 seconds
Programming for submaximal effort: Build to a moderate set of 5 in 6 sets
Programming for max effort: Build to a 1RM

All of the programming recommendations aren’t set in stone, so feel free to work in your own methods like max effort training, submaximal effort, repetition effort, strength-endurance, general strength work, as well as dynamic effort training.